Foam Knee Braces Installed

I used the foam knee brace kit that Pygmy sells. Pretty basic but it works well.

You get two pieces of soft white foam and two pieces of triangular rigid foam. The idea is that you use contact cement to glue the two together. See picture below. Then you glue the entire thing underneath the deck panel where your knees go.

The picture below is showing the PORT knee brace (yes, I know it says starboard on the foam but I messed up and corrected it). The idea is that the triangular bit it held next to your knee, but the thinner bit it padding between your knee and the deck panel.

Sit in the boat and put the glued up foam above your knee and under the deck. Position it at an angle pointing outward in-line with your legs. Mark underneath on the deck panels where you want the foam. The sand the areas you marked. Apply contact cement to both the foam and the deck. Wait until it's dry and then place the foam onto the deck panel. Use a sharp kitchen knife to trim it flush to the coaming.

This is an older picture from a different kayak, but the idea is exactly the same. You can see how the knee brace is angled out and would be in-line with your knee.

Next step... the maiden paddle!

Peace!

Comments

The Rogue Manual

I've posted about this earlier, but thought it might be good to post it again for anyone who may be interested. I've started to write a manual of tips and tricks for Pygmy solo kayak builders. It covers the taping method, so that your boat doesn't have hundreds of holes all over it. I'm on version 2 now. Version 2 covers several other tips and tricks from myself and from others as collected over time. ATTENTION : Use the manual at your own risk! The only person responsible for any mistakes or problems with the building of your boat is you. Always use the official Pygmy manual that came with your kit. Only do those tips and tricks that make sense to you. If something in the manual doesn't sound right to you, then don't do it! Neither I, nor Pygmy Boats, nor anyone else except YOU is responsible for the safety of your boat and the quality of your build. It's in very rough draft form right now, but if you'd like to read it, please send a $10 donat...

Annapolis Wherry Hull Painted

If you haven't yet, please read my previous post regarding amine blush and primers. After thoroughly washing the hull with water, and then priming, I was now ready for top coating. I used Interlux Toplac Plus in Matterhorn White. What a great paint! OMG... this stuff seems to have magical properties! I've never used a paint that does not sag or run, even on vertical hull sides. Of course, you have to roll on a light coat with a foam roller, but even with a thin coat like that, most paints would still have runs. This one doesn't! And you don't need to tip it either! Just roll it on and walk away. It gets better too... you don't have to sand after each coat! As long as you roll on a second coat after 16 hours but before 3 days, you don't have to sand. Nice! I did three coats in three days with no sanding between coats. There's a slight bit of orange peel, but most of the surface issues are due to my poor surface prep instead of orange peel. To be honest, ...

Waterlog Surfboard Build, Part 2

Since my last post I've made a lot of progress. I've completed the rails and the landing strips. Here is the chine log being epoxied in. By the way, I'm using epoxy for much of this. I ended up using Titebond III for most of the rails because they didn't have a lot of force on them and I could get them clamped down quickly (Titebond III sets quickly). But for anything that has any stress on it, I'm using WEST System epoxy that I have left over. The nose strips had to be steamed. Read the manual for how to do this. It works well enough. For the landing strips (the 'lands'), I'm doing the "alternative" method that is shown in one of Grain's tutorial videos . I'm running the outside one out the ends. It worked out well and I'd definitely recommend you do it instead of the convoluted approach they say in their manual. I would expect that at some point in the future that they make this the primary way to do it and change their m...

Search This Blog